Видео

They should have angled the tip down more so you dont melt your turn signal like I did on my 2009 450 exc.

Would a 7/32” drill bit work? That’s 1/64” bigger than you said in the video

Do you need to do any tuning after you install?

How tf did you do that?! My shock won’t allow me to do that. Some how the shock needs to be compressed big time in order for me to get any bolts in either side.

removing spark arrestor to install another spark arrestor 🤦🏼so dumb. do actually ppl buy it?

Why can't the pulse bar handle the lights? the only difference is the pulse bar has a 40amp fuse the post doesn't.

I cannot find that part anywhere. Where can I find the door mount kit?

saved me a ton of time. Ty for making this video

Did anyone order from Rocky Mountain ATV and they sent you the wrong fit-kit? Because they sent me four bolts instead of just two, and the fit kit they sent me had too big of bolts.

Your kickstand for the YZ250 can you use it while starting the bike

I've yz450f 2013 with stock exhust I need it share to me link

How do I get the barrel out if I don’t have the press pin

What do I do if I’ve got a set of used fastway pegs with the fit kit already installed and I need to swap the fit kit? I don’t have a press, vice, or the installation tool that comes with the pegs

🤷 'promosm'

Thanks for the video. I would have totally forgotten the RTV.

Just a note that may save some of you time. I installed in the lowering position on my 22 YZ250 F, you will need the collar an 4 shims on each side to match the camber of the stock foot pegs. 3 shims/washers each side is perfectly level. You will need to use the longer bolts that come in the fit kit as well. If you install in the lower position, you'll need to adjust your shift lever and brake lever lower as well.

I wonder how many bikes actually started a forest fire? Probably 0-1 ever

What I like about this rack is that once it’s installed on the subframe it’s now two bolts to remove and reinstall. 👍

Nope, I'm out

will these work in the lower position on a YZ450?

When are these available?

I think applying spark arrestors to illegal aliens would do a lot more good than putting them on motorcycles.

I'm not sure what others were expecting but took me all of 10 mins to remove my old end cap and install the new one.. perfect fit! Looks great.

I'm trying to fit the Evo 4 to my 2019 yz250 as we speak. My spring keeps popping out the hole every time I flick the peg up

Economical ? Really! The FISCH is less than half the price and literally slips in the stock pipe . NICE TRY !

What is this? What for? What does it do and why is it better than other foot pegs?

Where is the USFS stamp ?

I installed mine yesterday. It would've been nice to have some basic directions. Such as: what size drill bit to make the pilot holes. I had to eyeball it, and probably used a bit one size too small, but I was able to use a drill/driver to send the self-tapping screws go in (very tightly). No mention of Locktite on any of the screws (no directions, again).

Good luck this year Wyatt. I'll be keeping an eye on you in PulpMX Fantasy ;)

The video seems like it could be reshot and edited to turn your second thoughts into a smoother video, but it was helpful to watch and helped make my installation more familiar. Worked great, and what a great rack this is. Thanks!

Best pegs out there! I run the Air-EXT with the F7 cleats!

Why won't the OEM Guy's just put this stuff on from the factory!! everyone knows the OEM Stand sucks. just like the Carbs on all the 2 strokes suck, just add an Lectron or Smart Carb and be done...

Great concept, But the final appearance looks rubbish. If you made it look like one piece and took the hard edges out of it you would sell heaps more. ''Just saying''!!

You forgot to use Loctite.

thats not a cresent

Could this work on a crf150r

No need to torque those bolts?

Seal a cone

Awesome 🤙🏼question do you sell one for my 2020 kawasaki KLX300R if not will you be making one ?

Looks like a solid bit of kit, but that level of bike mutilation is a little too much for me. I think I'll try fashioning my own rack using the exhaust bolt holes and the sub-frame end fixtures.

Nice video and would they able fit on lexx mxe and what other exhaust do they fit on cheers

I don’t know how you got the 250 star key out so easily mine is not coming out even if I use a drill

Been stuck in the Cotter pin for an hour

that really makes those bars super high 😯

Could this work on a 2017 crf 250 ?

worthless, when you don't show how they work.

2017 KTM EXC-F 350 EXC-F: pro-moto billet part 01-3211 is a different video (and it is only 6 minutes long and easier to install). Go to ProMotoBillet.com --> SUPPORT --> Manuals --> Cargo Racks --> 01-3211 and download new instructions and new templates and watch the new video. PMB has awesome customer service and support.

My Rack Shrink Pack did not come with the paper templates. Is it online somewhere?